Coulomb per second to Nanoampere
C/s
nA
Conversion History
| Conversion | Reuse | Delete |
|---|---|---|
| No conversion history to show. | ||
Quick Reference Table (Coulomb per second to Nanoampere)
| Coulomb per second (C/s) | Nanoampere (nA) |
|---|---|
| 0.1 | 100,000,000 |
| 1 | 1,000,000,000 |
| 5 | 5,000,000,000 |
| 10 | 10,000,000,000 |
| 20 | 20,000,000,000 |
| 100 | 100,000,000,000 |
About Coulomb per second (C/s)
The coulomb per second (C/s) is a derived SI expression for electric current that makes the physical definition explicit: one ampere is exactly one coulomb of charge passing a point per second. The relationship I = Q/t links current (A), charge (C), and time (s). While C/s and A are numerically identical and dimensionally equivalent, the C/s form appears in physics textbooks and dimensional analyses where the derivation from charge and time is instructive rather than treating the ampere as primitive. In calculations tracking charge accumulation — capacitor discharge, electroplating, or battery coulomb-counting — expressing current in C/s clarifies the unit chain.
A capacitor delivering 1 C of charge over 1 second discharges at exactly 1 C/s = 1 A. A 500 mA USB charger transfers 0.5 C of charge each second.
About Nanoampere (nA)
The nanoampere (nA) equals one billionth of an ampere (10⁻⁹ A) and is used for the smallest measurable electrical currents in precision instrumentation and low-power electronics. Electrochemical biosensors detecting glucose or DNA generate signals in the nanoampere range; implantable devices are designed to draw only a few nanoamperes in sleep states to extend battery life by years. Junction leakage currents in CMOS transistors and reverse-bias diode currents are also measured in nanoamperes. In electrochemistry, nanoampere-resolution galvanostat equipment is standard for corrosion studies and thin-film deposition research.
A glucose biosensor strip draws approximately 100–500 nA during a measurement. A low-power microcontroller in deep sleep typically consumes 1–100 nA.
Coulomb per second – Frequently Asked Questions
Why bother writing coulombs per second when it is just amperes?
In dimensional analysis and physics derivations, C/s makes the relationship between charge and current explicit. When you are computing how much silver an electroplating bath deposits (Faraday's law), writing current as C/s reminds you that charge = current × time, which directly gives the mass deposited.
How many electrons is one coulomb?
One coulomb is approximately 6.242 × 10¹⁸ electrons — about 6.2 quintillion. At 1 C/s (1 A), that many electrons pass a point in your wire every single second. A USB cable charging your phone at 2 A carries 12.5 quintillion electrons per second. The numbers are staggering but the charges are tiny.
Is coulombs per second used in any real-world instrument or specification?
Not directly — every instrument reads in amperes or milliamperes. But coulomb-counting battery fuel gauges internally track charge in coulombs by integrating current over time: ∫I dt. The C/s framing appears in battery management system firmware and electrochemistry literature where charge balance matters.
How does Faraday's law of electrolysis use coulombs to predict metal deposition?
Faraday discovered that the mass of metal deposited at an electrode is directly proportional to the total charge passed (in coulombs). For silver, 107.87 grams deposit per 96,485 C (one Faraday). So a 10 A electroplating bath running for 1 hour passes 36,000 C and deposits about 40 g of silver. Thinking in C/s makes the calculation: current × time × atomic weight / (valence × 96,485).
How does coulomb counting work in battery management systems?
A shunt resistor or Hall sensor continuously measures current flowing in and out of the battery. The BMS integrates this current over time (summing C/s × Δt) to track net charge. Drift and measurement errors accumulate, so smart BMS designs periodically recalibrate against voltage-based state-of-charge estimates.
Nanoampere – Frequently Asked Questions
Why does my microcontroller datasheet list nanoampere sleep currents?
Chip designers optimize deep-sleep modes to leak only 1–100 nA so a coin cell battery (225 mAh) can power the device for 5–10 years without replacement. Every nanoampere matters in IoT sensors deployed in remote locations where battery swaps are impractical or impossible.
Can you actually measure a single nanoampere of current?
Yes — picoammeters and source-measure units (SMUs) from Keithley or Keysight resolve currents down to 0.01 nA. The trick is shielding: at nanoampere levels, even humidity on a PCB trace or triboelectric effects from cable movement can introduce errors larger than the signal itself.
What biological processes produce nanoampere-level currents?
Individual ion channels in cell membranes pass about 2–10 picoamperes each, but clusters of channels in a patch-clamp experiment produce nanoampere signals. Electrochemical glucose sensors generate 50–500 nA proportional to blood sugar levels. Neural signal electrodes also detect nA-scale biocurrents.
How does nanoampere leakage current affect circuit design?
At nanoampere levels, leakage through PCB substrates, capacitor dielectrics, and transistor junctions becomes significant. High-impedance analog circuits must use guarded traces, Teflon standoffs, and low-leakage components. A fingerprint on a circuit board can introduce 1–10 nA of leakage from moisture absorption.
How many electrons per second is one nanoampere?
One nanoampere is about 6.24 billion electrons per second (6.24 × 10⁹ e/s). That sounds like a lot, but it is literally a billionth of the electron flow in a one-ampere current. Counting individual electrons at this rate is the basis of quantum current standards being developed at national metrology labs.