Weber per henry to Milliampere
Wb/H
mA
Conversion History
| Conversion | Reuse | Delete |
|---|---|---|
1 Wb/H (Weber per henry) → 1000 mA (Milliampere) Just now |
Quick Reference Table (Weber per henry to Milliampere)
| Weber per henry (Wb/H) | Milliampere (mA) |
|---|---|
| 0.1 | 100 |
| 1 | 1,000 |
| 5 | 5,000 |
| 10 | 10,000 |
| 20 | 20,000 |
| 100 | 100,000 |
About Weber per henry (Wb/H)
The weber per henry (Wb/H) equals one ampere, derived from inductance: the magnetic flux Φ stored in an inductor equals inductance L times current I (Φ = L·I), so I = Φ/L = Wb/H. This form appears in electromagnetic field theory and inductor design where engineers compute the current required to establish a given magnetic flux in a core. One weber of flux in a one-henry inductor corresponds to exactly one ampere of magnetising current. The Wb/H notation is common in transformer and motor design calculations, magnetic circuit analysis, and advanced EMC engineering where field and circuit quantities must be reconciled.
A 1 H inductor carrying 5 A stores 5 Wb of magnetic flux — expressed as 5 Wb/H. Power transformer core saturation analysis links flux density to Wb/H magnetising current.
About Milliampere (mA)
The milliampere (mA) equals one thousandth of an ampere (10⁻³ A) and is the practical unit for most consumer electronics and lighting circuits. USB 2.0 ports supply up to 500 mA; USB-C Power Delivery can reach 5,000 mA (5 A). A standard 5 mm indicator LED operates at 10–20 mA; mid-power LED drivers supply 100–350 mA. Human perception of electric shock begins near 1 mA; currents above 10 mA cause involuntary muscle contraction, and above 100 mA can be lethal. Wireless sensors, earphones, and small motors typically draw single-digit to low-hundreds of milliamperes.
A USB 2.0 port provides up to 500 mA for charging. A standard 5 mm indicator LED operates at around 20 mA.
Weber per henry – Frequently Asked Questions
Why would a transformer designer think in webers per henry?
When designing a transformer, you start with the required flux (webers) to transfer power at a given voltage and frequency. The core's inductance (henries) is set by geometry and material. Dividing flux by inductance gives the magnetising current that must flow — and if it is too high, the core saturates and the transformer overheats.
What is a weber in practical terms?
One weber is the magnetic flux that, when reduced to zero in one second, induces one volt in a single-turn coil. A small transformer core might carry 0.001 Wb (1 mWb) of peak flux. The Earth's magnetic field through a 1 m² loop is about 50 μWb. One weber is actually an enormous amount of flux in everyday terms.
What happens when the Wb/H calculation shows too much current?
If the calculated magnetising current (Wb/H) exceeds design limits, the core is approaching magnetic saturation. The inductance drops sharply, current spikes further, and the inductor or transformer overheats. Solutions include using a larger core, higher-permeability material, an air gap, or reducing the operating flux density.
How does core saturation relate to the Wb/H ratio?
Every magnetic core has a saturation flux density (e.g., 1.5 T for silicon steel, 0.3 T for ferrite). When flux approaches this limit, permeability collapses, inductance plummets, and Wb/H (current) shoots up. Power supply designers must ensure peak flux stays 20–30% below saturation under worst-case conditions.
How does an air gap in an inductor core change the Wb/H calculation?
An air gap dramatically increases the reluctance of the magnetic circuit, which lowers inductance (H) for the same core geometry. For a given flux (Wb), the magnetising current (Wb/H) increases — but the core is far harder to saturate. Power supply designers deliberately add 0.1–1 mm air gaps to ferrite cores so the inductor can handle higher peak currents without the flux density hitting saturation limits.
Milliampere – Frequently Asked Questions
How many milliamps is dangerous to a human?
The danger thresholds for 50/60 Hz AC are roughly: 1 mA (tingling), 10–20 mA (muscle lock — you cannot let go), 75–100 mA (ventricular fibrillation), and 200+ mA (cardiac arrest and burns). DC is somewhat less dangerous at the same current. Duration matters enormously — 100 mA for 1 second is more lethal than 100 mA for 10 ms.
Why is my phone charger rated in milliamps when it charges at 2 amps?
Battery capacity is rated in milliampere-hours (mAh), not milliamps. A 4,000 mAh battery holds 4,000 mA for one hour (or 2,000 mA for two hours). The charger delivers 2 A (2,000 mA) of current, and it takes about 2 hours to fill that 4,000 mAh battery from empty.
What is the milliamp draw of common household items?
A wireless earbud draws 5–15 mA during playback. A TV remote uses about 10 mA when pressing a button. An LED nightlight consumes 20–50 mA. A smoke detector in standby draws 10–30 μA (0.01–0.03 mA) — so low it runs on a 9V battery for years.
Why do LED specifications always mention 20 mA?
Standard 5 mm indicator LEDs were designed around a 20 mA operating point — bright enough to see clearly, low enough to avoid overheating the tiny die. All datasheet specs (luminous intensity, color, forward voltage) are measured at this "test current." High-power LEDs use 350 mA or 700 mA as their reference instead.
How does milliamp-hour (mAh) relate to milliamp (mA)?
Milliamp-hours measure charge capacity; milliamps measure current flow rate. A 2,000 mAh battery can deliver 2,000 mA for 1 hour, or 200 mA for 10 hours, or 20 mA for 100 hours — current times time equals capacity. Dividing mAh by mA gives approximate runtime in hours.