Tebibyte to Mebibit

TB (terabyte) = 10¹² bytes = 1,000,000,000,000 bytes (SI decimal). TiB (tebibyte) = 2⁴⁰ bytes = 1,099,511,627,776 bytes (IEC binary). TiB is 9.95% larger. The practical consequence: a 1 TB hard drive (decimal) holds 0.9095 TiB. This 10% gap is the primary reason drive capacity appears lower in the OS than on the box.

ZFS and Btrfs are copy-on-write filesystems designed for TiB-scale pools with built-in features that traditional filesystems lack. ZFS supports inline deduplication — a 10 TiB pool with 40% duplicate data might show 6 TiB of logical usage but only consume 3.6 TiB physically. Btrfs offers transparent compression (zstd), where a 4 TiB dataset of compressible log files might occupy only 1–2 TiB on disk. Both support snapshots that initially consume zero extra space, growing only as data diverges. These features make "used space in TiB" surprisingly complex to report accurately.

Yes. Linux tools (df -h, lsblk) display storage in IEC binary units: KiB, MiB, GiB, TiB. df -h output showing "1.8T" for a 2 TB drive is reporting 1.8 TiB. Modern Linux distributions correctly label these as TiB in technical contexts. This is one of the areas where Linux is more technically precise than Windows or consumer storage labels.

RAID arrays lose capacity to redundancy: RAID 1 mirrors two drives (50% efficiency); RAID 5 loses one drive worth of capacity; RAID 6 loses two drives. A 4-drive RAID 5 array of 2 TB drives has 3 × 2 TB = 6 TB raw usable (decimal), ≈ 5.46 TiB, minus filesystem overhead. Enterprise storage also reserves space for spares, snapshots, and wear levelling, further reducing usable TiB.

No. A tebibyte (TiB) = 2⁴⁰ bytes = 1,099,511,627,776 bytes — about 1.1 trillion bytes. Exactly one trillion bytes = 10¹² bytes = 1 terabyte (TB, decimal). The tebibyte is approximately 10% larger than a trillion bytes. "Terabyte" is often casually used to mean "1 trillion bytes"; "tebibyte" is the precise binary equivalent at 1,024 gibibytes.

A megabit (Mb) = 1,000,000 bits (SI decimal). A mebibit (Mibit) = 1,048,576 bits (IEC binary = 2²⁰ bits). The mebibit is 4.857% larger. Network speeds use megabits (Mb); embedded memory and flash storage specifications use mebibits when binary precision is required.

Mebibit appears primarily in microcontroller and microprocessor datasheets (e.g. "2 Mibit flash memory"), FPGA configuration file sizes, and some wireless protocol standards (802.11 frame size limits, Bluetooth payload specifications). It is rarely seen in consumer-facing applications but is common in embedded systems engineering documentation.

Yes. In 2007, a class-action settlement required Western Digital to pay $2.1 million because their hard drives advertised capacity in decimal megabits/gigabits while operating systems reported binary values — making drives appear ~7% smaller than labeled. Similar suits hit Seagate and Samsung. These lawsuits accelerated industry adoption of IEC prefixes and pushed Apple (2009) and later Windows (2021) to clarify their capacity labeling.

SPI flash chips are addressed at the bit level during serial communication — the programr shifts data in one bit at a time over the SPI bus. Datasheets specify capacity in mebibits (e.g. W25Q16 = 16 Mibit = 2 MiB) because the serial interface operates on bits, not bytes. Calculating transfer time requires bit-level math: reading a full 16 Mibit chip at 80 MHz SPI clock takes about 0.2 seconds.

Flash memory chips organise storage in binary-aligned blocks (sectors, pages) whose sizes are powers of 2. Specifying capacity in mebibits (1,048,576 bits per Mibit) maps precisely to the physical organisation of the memory array. Using decimal megabits would result in non-integer block counts, making datasheet specifications harder to verify against hardware design.