British Thermal Units to Inch-Ounce

US HVAC manufacturers adopted BTU/hour because heating and cooling equipment historically measured heat removal or addition, not electrical input. A 12,000 BTU/h window unit removes 12,000 BTU of heat per hour from a room — that figure directly tells you the cooling capacity. Watts measure electrical power consumed, which is less due to the efficiency (EER) of the unit. The convention stuck because the entire US supply chain uses it.

A rough rule of thumb is 20 BTU per square foot of living space in a temperate climate. A 300 sq ft bedroom needs about 6,000 BTU/h; a 1,500 sq ft open-plan living area needs roughly 30,000 BTU/h. Actual requirements vary with insulation, ceiling height, climate zone, and window area. Poorly insulated older homes may need 30–40 BTU per square foot.

BTU is a unit of energy (heat); BTU/h is a unit of power (rate of heat flow). When an air conditioner is labelled "12,000 BTU," the industry shorthand actually means 12,000 BTU per hour. Technically one BTU equals about 1,055 joules of energy, while 1 BTU/h equals about 0.293 watts. The distinction matters for energy calculations but is routinely blurred in product marketing.

US natural gas is priced in dollars per million BTU (MMBtu) at the wholesale level and dollars per therm (100,000 BTU) on residential bills. One cubic foot of pipeline gas contains roughly 1,020 BTU. The Henry Hub benchmark price of $2.50/MMBtu means each therm costs about $0.25 wholesale — residential prices are higher after delivery and utility markups.

The UK metricated energy units in the 1970s–1990s, switching gas billing from therms (100,000 BTU) to kilowatt-hours and scientific work to joules. The "British" in BTU reflects 19th-century British steam engineering origins, not current usage. Today the BTU is almost exclusively an American unit, used for HVAC, gas pricing, and appliance ratings across the US.

RC servo motors are rated by torque in inch-ounces (or oz·in) because the forces involved are tiny. A standard micro servo produces 40–60 in·oz, which is enough to deflect a model aircraft aileron. High-torque digital servos for 1/10-scale RC cars reach 200–400 in·oz. The inch-ounce scale gives hobbyists whole-number specs that are easy to compare.

Servo motors produce more torque at higher voltage because the motor windings draw more current and generate a stronger magnetic field. A servo rated at 60 in·oz at 4.8 V might deliver 75 in·oz at 6 V — a 25% boost. RC pilots choose voltage based on the tradeoff: 6 V gives snappier response and more holding torque for aerobatics, but draws more current and generates more heat, reducing servo lifespan. Competition flyers often run 7.4 V for maximum performance, accepting shorter gear life.

Inch-ounces give convenient whole numbers for very small torques where newton-meters would be awkward decimals (e.g., 50 in·oz ≈ 0.353 N·m). The RC hobby, miniature clockwork, and precision instrument industries in the US developed around imperial units, and the convention persists even as SI gains ground. Many datasheets now list both units side by side.

A mechanical wristwatch mainspring delivers roughly 2–5 in·oz of torque. Larger mantel clocks may have mainspring torques of 10–30 in·oz. Escapement adjustments are even finer, sometimes below 1 in·oz. Horologists use inch-ounces (or gram-centimeters) because these scales match the delicate forces in timekeeping mechanisms.

A servo's inch-ounce rating tells you the maximum force it can exert at one inch from the output shaft. A 100 in·oz servo can hold 100 ounces (6.25 lb) at 1 inch, or 50 ounces at 2 inches. Robotics designers use this to size servos for joint loads — a small robotic arm lifting 1 lb at 4 inches needs at least 64 in·oz, plus a safety margin of 50% or more.