Megawatt Hour to Inch-Pound

MWh is the natural unit for grid-scale transactions because power plants and large industrial loads operate in the megawatt range. Quoting in kWh would produce unwieldy numbers — a 1 GW nuclear plant generates 24,000 MWh/day, not 24,000,000 kWh. Spot markets like the US PJM or European EPEX quote prices in $/MWh or €/MWh, typically $20–$80/MWh in normal conditions.

One MWh powers the average US home for about 1.1 months (since the average is 886 kWh/month). In Europe, where consumption is lower (~300 kWh/month), one MWh can cover about 3.3 months. A single MWh is also enough energy to drive an electric car about 5,000–6,000 km, or to run an industrial air compressor for roughly 4 hours.

US wholesale prices typically range from $20 to $80/MWh depending on region, time of day, and fuel costs. European prices are generally higher at €50–€150/MWh. During extreme events — heat waves, supply shortages — prices can spike above $1,000/MWh for brief periods. Negative prices (below $0/MWh) also occur when wind or solar oversupply the grid.

A modern onshore 3 MW turbine at 35% capacity factor produces about 9,200 MWh/year. A large offshore 15 MW turbine at 50% capacity factor generates roughly 65,700 MWh/year. Capacity factor — the percentage of theoretical maximum output actually achieved — varies with wind resource, turbine technology, and maintenance downtime.

Current lithium-ion battery costs (~$150–250/kWh) make 4-hour systems economical for peak shaving and solar time-shifting, but 24-hour storage would cost 6× more with diminishing returns. Grids instead layer solutions: batteries handle the evening peak (4 h), gas turbines cover overnight baseload, and pumped hydro or compressed air provide longer-duration backup. Iron-air and flow batteries are emerging for 100+ hour storage at lower cost per kWh, potentially closing the gap by the 2030s.

Inch-pounds provide finer resolution for small fasteners where foot-pound values would be fractions (e.g., 3 in·lb vs 0.25 ft·lb). Electronics assembly, firearms scope mounting, and bicycle component installation all specify inch-pounds because over-torquing a small screw by even one foot-pound can strip threads or crack housings.

On an M3 screw into aluminum (spec: 5 in·lb), exceeding by 2 in·lb — a 40% overload — can strip the threads or crack a thin boss. Small fasteners have almost no safety margin because the thread engagement area is tiny and the materials (plastic, aluminum, brass) are soft. This is why electronics repair shops use beam-type or preset click torque drivers accurate to ±0.5 in·lb, and why aerospace assembly procedures treat inch-pound specs as hard limits, not suggestions.

Laptop hinge screws typically require 2–5 in·lb, hard drive mounting screws 2–4 in·lb, and motherboard standoff screws 5–8 in·lb. Going beyond the spec risks cracking plastic bosses or stripping soft aluminum threads. A precision bit driver with a torque limiter is essential for electronics repair work.

Dimensionally they are identical — force times distance — but context differs. As torque, 1 in·lb means one pound-force applied at one inch from a pivot. As energy, it means one pound-force pushing through one inch of linear displacement (0.11299 J). In practice, inch-pounds almost always refer to torque in mechanical specifications.

Scope rings and bases use small screws that are easily damaged, and consistent clamping force is critical for zero retention under recoil. Typical specs are 15–25 in·lb for ring screws and 30–65 in·lb for base screws. Under-torquing lets the scope shift; over-torquing cracks the scope tube or strips the screw. A dedicated inch-pound torque wrench is considered essential kit for precision rifle setup.