BTU/minute to Megawatt

During commissioning and troubleshooting, when measuring instantaneous heat output over a few minutes. If a furnace is cycling on/off and you're timing its burn cycle, you might measure 2,000 BTU/min during the 8-minute burn phase, then zero during the 4-minute off phase. This gives a clearer picture than the nameplate BTU/h rating, which assumes continuous operation and averages out the cycling.

Multiply by 60. A burner producing 1,500 BTU/min delivers 90,000 BTU/h. Going the other way, divide by 60: a 120,000 BTU/h furnace runs at 2,000 BTU/min when firing. This conversion is so routine in US HVAC work that technicians do it reflexively. The minute rate is more intuitive during short measurements; the hourly rate matches equipment nameplate conventions.

A gas stovetop burner on high: 150–250 BTU/min. A gas fireplace insert: 300–600 BTU/min. A residential water heater recovery: 500–700 BTU/min. A barbecue grill on full: 400–1,000 BTU/min. A clothes dryer: 350–600 BTU/min. These are all common US gas appliances where the original engineering was done in BTU-based units, and the nameplate may show BTU/h but the technician thinks in BTU/min during testing.

A 15 m² (160 sq ft) room in a cold climate needs roughly 100–250 BTU/min (6,000–15,000 BTU/h) of heating depending on insulation quality and outdoor temperature. A portable space heater rated 5,000 BTU/h delivers about 83 BTU/min — adequate for a small well-insulated room but insufficient for a drafty old one. The rule of thumb in US HVAC: 20–30 BTU/h per square foot, or about 0.4 BTU/min per square foot.

Almost never. The rest of the world uses watts or kilowatts for thermal power ratings. Even in countries that once used BTU (like the UK), equipment has long been rated in kW. Some Middle Eastern and Asian HVAC markets use BTU/h because they import US-manufactured equipment with American ratings, but BTU/min specifically is a niche US engineering convention. If you see it, you're almost certainly reading an American document.

In the US, roughly 750–1,000 homes (average consumption ~1.2 kW per home). In Europe, where usage is lower, 1 MW can serve 1,500–2,000 homes. But this is average — on a hot summer afternoon when everyone cranks AC, that number can drop to 300–400 homes. Grid planners must size for peak demand, not averages, which is why installed capacity far exceeds average load.

A small data center uses 1–5 MW; a large hyperscale facility (Google, AWS, Microsoft) draws 50–200 MW — some exceeding 300 MW. The entire US data center industry consumed about 17 GW in 2023, roughly 4% of national electricity. AI training clusters are pushing demand higher: a single large GPU cluster can draw 50–100 MW, and planned AI-focused campuses target 1 GW or more.

Onshore turbines typically rate 2–6 MW; the latest offshore monsters reach 14–16 MW per turbine. Vestas' V236-15.0 MW turbine has a rotor diameter of 236 meters — wider than two football fields. A single sweep of its blades can generate enough electricity for a UK household for two days. Capacity factors run 25–45% onshore and 40–55% offshore, so actual average output is roughly half the nameplate rating.

Most operating reactors produce 500–1,400 MW of electrical power. The world's largest, at France's Gravelines plant, has six reactors totalling 5,460 MW. Small Modular Reactors (SMRs) being developed target 50–300 MW each. Nuclear plants run at 85–95% capacity factor — far higher than wind (~35%) or solar (~25%) — meaning a 1,000 MW reactor actually delivers about 900 MW on average.

MW tells you the maximum instantaneous power the battery can deliver (how fast it can discharge), while MWh tells you total stored energy (how long it can sustain that output). A 100 MW / 400 MWh battery can deliver 100 MW for 4 hours, or 50 MW for 8 hours. Grid operators care about both: MW for handling sudden demand spikes, MWh for sustained backup during extended outages or evening solar fade.