BTU/minute to Terawatt

During commissioning and troubleshooting, when measuring instantaneous heat output over a few minutes. If a furnace is cycling on/off and you're timing its burn cycle, you might measure 2,000 BTU/min during the 8-minute burn phase, then zero during the 4-minute off phase. This gives a clearer picture than the nameplate BTU/h rating, which assumes continuous operation and averages out the cycling.

Multiply by 60. A burner producing 1,500 BTU/min delivers 90,000 BTU/h. Going the other way, divide by 60: a 120,000 BTU/h furnace runs at 2,000 BTU/min when firing. This conversion is so routine in US HVAC work that technicians do it reflexively. The minute rate is more intuitive during short measurements; the hourly rate matches equipment nameplate conventions.

A gas stovetop burner on high: 150–250 BTU/min. A gas fireplace insert: 300–600 BTU/min. A residential water heater recovery: 500–700 BTU/min. A barbecue grill on full: 400–1,000 BTU/min. A clothes dryer: 350–600 BTU/min. These are all common US gas appliances where the original engineering was done in BTU-based units, and the nameplate may show BTU/h but the technician thinks in BTU/min during testing.

A 15 m² (160 sq ft) room in a cold climate needs roughly 100–250 BTU/min (6,000–15,000 BTU/h) of heating depending on insulation quality and outdoor temperature. A portable space heater rated 5,000 BTU/h delivers about 83 BTU/min — adequate for a small well-insulated room but insufficient for a drafty old one. The rule of thumb in US HVAC: 20–30 BTU/h per square foot, or about 0.4 BTU/min per square foot.

Almost never. The rest of the world uses watts or kilowatts for thermal power ratings. Even in countries that once used BTU (like the UK), equipment has long been rated in kW. Some Middle Eastern and Asian HVAC markets use BTU/h because they import US-manufactured equipment with American ratings, but BTU/min specifically is a niche US engineering convention. If you see it, you're almost certainly reading an American document.

The Sun delivers about 173,000 TW to Earth's surface. Human civilisation uses roughly 18 TW total. So we'd only need to capture 0.01% of incoming solar energy to power everything — an area of solar panels roughly 400 km × 400 km, about the size of Montana. The challenge isn't total energy availability; it's cost, storage, transmission, and the fact that sunlight is spread thin and intermittent.

Imagine 18 trillion light bulbs burning continuously, or 9 billion people each running a 2 kW heater non-stop. That 18 TW figure includes everything — electricity, transport fuel, industrial heat, cooking, heating. About 40% comes from oil, 27% from coal, 24% from gas, and the rest from nuclear and renewables. The US alone accounts for about 3 TW despite having only 4% of world population.

Replacing all 18 TW of human energy with clean sources would require roughly 60–75 TW of installed solar capacity (accounting for ~25% average capacity factor). That's about 40 times current installed solar. At 2023 installation rates of ~0.4 TW/year, it would take 150 years — but installation rates are doubling every 2–3 years. If that exponential trend holds, we could theoretically reach 60 TW of solar within 15–20 years.

Earth radiates about 47 TW of geothermal heat from its interior, driven by radioactive decay and residual primordial heat. That's 2.5× human energy consumption, but it's spread across the entire surface at extremely low density (~0.09 W/m²). Iceland, sitting atop a mantle plume, exploits geothermal for 90% of its heating. Globally, geothermal electricity capacity is only about 16 GW — a tiny fraction of what's theoretically available.

No — the terawatt scale is a very recent phenomenon. In 1800, global human power consumption was about 0.5 TW (mostly biomass burning). By 1900 it reached 1 TW with coal industrialisation. We crossed 10 TW around 1985. The jump from 1 to 18 TW in just 120 years tracks almost perfectly with global population growth times rising per-capita energy use. Pre-industrial humans used about 0.1 kW each; Americans now average 10 kW per person.