Watt to BTU/hour

A standard USB charger draws 5–10 W, while fast chargers pull 18–65 W and some proprietary ones hit 120–240 W. The charger itself consumes about 0.1–0.3 W even when nothing is plugged in — so-called "vampire power." Over a year, a plugged-in-but-idle charger wastes roughly 2 kWh, costing pennies but multiplied across billions of chargers worldwide it adds up to gigawatt-hours of waste.

Both are identical — 1 W = 1 J/s — but the watt was named in 1889 to honor James Watt, who quantified engine power decades before the joule was formalised. Giving power its own name made practical engineering simpler: saying "a 60-watt bulb" is far catchier than "a 60-joules-per-second bulb." The naming also followed a 19th-century tradition of honoring scientists with SI units — volt, ampere, ohm, and watt all came from this era.

A resting adult generates about 80–100 W of thermal power, roughly equivalent to an old incandescent light bulb. During intense exercise this spikes to 300–500 W total metabolic output, though only 20–25% becomes mechanical work — the rest is waste heat. This is why a packed lecture hall gets stuffy fast: 200 students produce about 20 kW of heat, equivalent to running 20 space heaters.

A single lightning stroke delivers about 1–5 billion watts (1–5 GW) of instantaneous power, but only for 1–2 milliseconds. The total energy per bolt is surprisingly modest — roughly 1–5 billion joules compressed into microseconds, equivalent to about 250 kWh or one month of a US household. You could theoretically power a town for a second, but capturing it is impractical because the pulse is too brief and unpredictable.

Watts measure the rate of energy flow (like the speed of water through a pipe), while watt-hours measure total energy consumed over time (like the total volume of water). A 100 W bulb running for 10 hours uses 1,000 Wh (1 kWh). Your electricity bill charges per kWh, not per watt — so a 2,000 W heater running one hour costs the same as a 100 W lamp running 20 hours.

The classic rule: 20 BTU/h per square foot. A 300 sq ft bedroom needs about 6,000 BTU/h; a 500 sq ft living room about 10,000 BTU/h. But this varies wildly with sun exposure (+10% for south-facing), ceiling height, insulation quality, number of occupants (+600 BTU per person), and climate zone. A room above a pizza oven in Phoenix needs more than a basement in Seattle. When in doubt, oversize slightly — an undersized unit runs constantly and never reaches setpoint.

Undersizing is obvious — the unit runs constantly and never reaches the thermostat setpoint on hot days. But oversizing is worse in subtle ways. An oversized AC cools the air quickly then shuts off before removing enough humidity, leaving you with a clammy 72°F house. The short cycles also wear the compressor faster (startup is the hardest moment) and waste energy. A 1-ton oversize in a humid climate like Florida can raise indoor humidity from a comfortable 45% to a muggy 60%. Proper Manual J load calculations matter more than most homeowners realize.

Exactly 12,000 BTU/h. One ton of AC is the cooling effect of melting one short ton (2,000 lbs) of ice over 24 hours. The ice absorbs 288,000 BTU of heat as it melts (2,000 lbs × 144 BTU/lb latent heat), divided by 24 hours = 12,000 BTU/h. Residential systems run 1.5–5 tons; commercial buildings 10–500 tons. The "ton" unit persists because HVAC contractors think in tons — "that house needs a 3-ton unit" is faster than "that house needs 10.5 kW of cooling."

Modern units achieve 12–25 BTU/h per watt of electricity (SEER 12–25). A SEER 20 unit removes 20 BTU/h of heat for every watt consumed — effectively a 3:1 heat pump ratio. That 12,000 BTU/h window unit draws 500–1,000 W of electricity depending on efficiency. The best mini-splits achieve SEER 30+, removing 30 BTU/h per watt, making them cheaper to run than resistive electric heaters even in heating mode.

A gas furnace's BTU/h rating is its thermal output after combustion efficiency losses (typically 80–96% of fuel input). A heat pump's BTU/h rating is the heat delivered including energy moved from outside — at COP 3, a heat pump delivering 36,000 BTU/h uses only 12,000 BTU/h worth of electricity. This makes direct BTU/h comparisons misleading: a 60,000 BTU/h furnace and a 60,000 BTU/h heat pump deliver the same heat, but the heat pump uses one-third the energy.