Centimeter Water (4 °C) to Millimeter Water (4 °C)
cmH2O
mmH20
Conversion History
| Conversion | Reuse | Delete |
|---|---|---|
| No conversion history to show. | ||
Quick Reference Table (Centimeter Water (4 °C) to Millimeter Water (4 °C))
| Centimeter Water (4 °C) (cmH2O) | Millimeter Water (4 °C) (mmH20) |
|---|---|
| 1 | 10.00000000000000000000043685845326149 |
| 5 | 50.00000000000000000000014480368846323 |
| 10 | 100.00000000000000000000028960737692646 |
| 15 | 150.00000000000000000000043441106538969 |
| 20 | 199.99999999999999999999955947046493081 |
| 100 | 999.99999999999999999999983684090249827 |
| 1,033 | 10,329.99999999999999999999952806222662444 |
About Centimeter Water (4 °C) (cmH2O)
The centimeter of water at 4 °C (cmH₂O) equals approximately 98.064 pascals — ten times the mmH₂O unit. It is the standard pressure unit in respiratory medicine and intensive care: positive end-expiratory pressure (PEEP), peak inspiratory pressure, and continuous positive airway pressure (CPAP) for sleep apnoea are all specified in cmH₂O. Cerebrospinal fluid pressure measurements also use cmH₂O. The unit spans a clinically convenient range, covering both physiological pressures and therapeutic ventilator settings.
CPAP therapy for sleep apnoea is prescribed at 4–20 cmH₂O. Normal cerebrospinal fluid pressure is about 10–18 cmH₂O in the lying position.
About Millimeter Water (4 °C) (mmH20)
The millimeter of water at 4 °C (mmH₂O) is the pressure exerted by a 1 mm column of pure water at its maximum density, equal to approximately 9.807 pascals. It is used for very low pressure measurements where even pascals give large numbers: HVAC duct static pressures, spirometry and respiratory mechanics, building ventilation system balancing, and manometer readings in laboratory work. The 4 °C reference ensures maximum water density and measurement reproducibility.
HVAC supply duct static pressures typically range from 25 to 250 mmH₂O. A forced exhalation against resistance generates roughly 10–50 mmH₂O.
Centimeter Water (4 °C) – Frequently Asked Questions
Why is CPAP pressure prescribed in cmH₂O and not in a more standard unit?
Respiratory medicine adopted cmH₂O because the original ventilators literally used water columns to regulate pressure — a jar of water with a submerged tube set the pressure at whatever depth the tube was immersed. A CPAP setting of 10 cmH₂O meant the air bubbled out at 10 cm depth. The unit stuck even after electronics replaced water seals, because clinicians, patients, and device manuals all speak the same scale.
What CPAP pressure in cmH₂O do most sleep apnoea patients use?
Most adults are prescribed between 6 and 14 cmH₂O, with 10 cmH₂O being a common starting point. Severe obstructive sleep apnoea may require 15–20 cmH₂O. Auto-titrating (APAP) machines vary pressure within a set range — typically 4–20 cmH₂O — adjusting breath by breath. Higher pressures are more effective at splinting the airway open but can cause discomfort and air swallowing.
How does cmH₂O relate to the ventilator pressures used in intensive care?
ICU ventilators also use cmH₂O. Positive end-expiratory pressure (PEEP) is usually set at 5–15 cmH₂O to keep alveoli open. Peak inspiratory pressure above 30–35 cmH₂O raises the risk of lung injury. Plateau pressures are monitored to stay below 30 cmH₂O. The entire field of mechanical ventilation runs on this single unit because it directly corresponds to the pressures inside the lung.
What is a normal cerebrospinal fluid pressure in cmH₂O?
Measured via lumbar puncture with the patient lying on their side, normal CSF pressure is 10–18 cmH₂O in adults. Above 25 cmH₂O suggests raised intracranial pressure — potentially from a tumor, meningitis, or hydrocephalus. Below 6 cmH₂O indicates low pressure, often from a CSF leak. Neurologists use cmH₂O rather than mmHg because spinal fluid is essentially water, making the unit a direct physical analogue.
How do you convert cmH₂O to millibars or kilopascals?
1 cmH₂O ≈ 0.981 mbar ≈ 0.0981 kPa. For bedside estimates, 1 cmH₂O ≈ 1 mbar is close enough (error under 2%). A CPAP setting of 12 cmH₂O is about 11.8 mbar or 1.18 kPa. Since respiratory equipment universally reads cmH₂O, conversion is mainly needed when interfacing with industrial instruments or when charting pressures alongside blood gas data reported in mmHg.
Millimeter Water (4 °C) – Frequently Asked Questions
Why is HVAC duct pressure measured in millimeters of water instead of pascals?
HVAC technicians originally measured duct pressure with a simple U-tube manometer filled with water — you literally read the height difference in millimeters. One mmH₂O ≈ 9.81 Pa, so a typical 25–250 mmH₂O duct pressure range corresponds to 245–2,450 Pa. The water column scale is still used because the instruments are cheap, intuitive, and field-rugged, even though digital gauges now display the same numbers electronically.
What does the "at 4 °C" part of the unit mean?
Water reaches maximum density at 3.98 °C (roughly 4 °C), where one cubic centimeter weighs exactly 1 gram. Specifying 4 °C ensures the pressure per millimeter of column height is reproducible and standardized. At 20 °C, water is about 0.2% less dense, introducing a tiny error. For most HVAC and lab work the difference is negligible, but calibration labs insist on the 4 °C reference for traceability.
How do you read a water manometer in mmH₂O?
Connect one side of a U-tube to the duct and leave the other open to atmosphere. The water level drops on the pressurized side and rises on the open side. The total height difference in millimeters is the gauge pressure in mmH₂O. Inclined (slant) manometers amplify small readings by tilting the tube — a 10:1 slope makes each millimeter of travel represent 0.1 mmH₂O, improving resolution for filter pressure-drop testing.
What mmH₂O range indicates a clogged HVAC filter?
A clean residential furnace filter creates 12–50 mmH₂O of pressure drop. When the drop exceeds 125–250 mmH₂O (varies by manufacturer), the filter is restricting airflow enough to hurt efficiency and strain the blower motor. Commercial systems set alarms at specific mmH₂O thresholds — when the differential pressure sensor hits the limit, a "replace filter" indicator lights up on the building management system.
How does mmH₂O relate to inches of water column (inH₂O)?
1 inch of water = 25.4 mmH₂O (since 1 inch = 25.4 mm). US HVAC specs use inches of water gauge (often written "in. w.g."); European and Asian specs use mmH₂O. If a US furnace manual says "maximum 0.5 in. w.g. static pressure," that is 12.7 mmH₂O. The conversion is just the familiar inch-to-millimeter factor applied to a column of water.