Kilogram-force per Square Centimeter to Centimeter Water (4 °C)

One technical atmosphere (symbol "at") is defined as exactly 1 kgf/cm² — the pressure exerted by a 1 kg mass on a 1 cm² area under standard gravity. It equals 98,066.5 Pa, roughly 3.6% less than a standard atmosphere (101,325 Pa). Russian and Japanese engineering standards used it heavily through the 20th century, and you will still find it on older boiler plates, hydraulic presses, and pressure vessel nameplates across Asia and Eastern Europe.

Japanese Industrial Standards (JIS) and Soviet-era GOST standards specified kgf/cm² for decades, and millions of gauges, compressors, and hydraulic machines built to those specs remain in service. Replacing a working gauge just to change the scale is wasteful, so factories keep using kgf/cm² alongside newer SI instruments. Modern JIS standards accept both, but legacy equipment is everywhere.

Multiply kgf/cm² by 14.22 to get psi, or by 0.981 to get bar. For quick mental math: 1 kgf/cm² ≈ 1 bar ≈ 14.2 psi ≈ 1 atmosphere. The errors in those approximations are all under 4%, which is close enough for field work. For precision, use the exact factor: 1 kgf/cm² = 98,066.5 Pa.

Small hydraulic jacks operate at 50–100 kgf/cm². Excavator hydraulics run at 250–350 kgf/cm². Industrial presses for stamping car body panels can reach 500–1,000 kgf/cm². The highest-pressure hydraulic systems — used in forging and isostatic pressing — operate above 3,000 kgf/cm², squeezing metal powder into near-net-shape parts.

Officially, yes — the SI discourages kilogram-force entirely, and international standards bodies prefer pascals, bar, or psi. Practically, the phase-out is glacially slow. New equipment in Japan and Russia increasingly uses MPa or bar, but service manuals, legacy calibrations, and replacement parts will reference kgf/cm² for decades to come. Knowing the conversion (×0.0981 for MPa) remains a useful skill for anyone working with imported machinery.

Respiratory medicine adopted cmH₂O because the original ventilators literally used water columns to regulate pressure — a jar of water with a submerged tube set the pressure at whatever depth the tube was immersed. A CPAP setting of 10 cmH₂O meant the air bubbled out at 10 cm depth. The unit stuck even after electronics replaced water seals, because clinicians, patients, and device manuals all speak the same scale.

Most adults are prescribed between 6 and 14 cmH₂O, with 10 cmH₂O being a common starting point. Severe obstructive sleep apnoea may require 15–20 cmH₂O. Auto-titrating (APAP) machines vary pressure within a set range — typically 4–20 cmH₂O — adjusting breath by breath. Higher pressures are more effective at splinting the airway open but can cause discomfort and air swallowing.

ICU ventilators also use cmH₂O. Positive end-expiratory pressure (PEEP) is usually set at 5–15 cmH₂O to keep alveoli open. Peak inspiratory pressure above 30–35 cmH₂O raises the risk of lung injury. Plateau pressures are monitored to stay below 30 cmH₂O. The entire field of mechanical ventilation runs on this single unit because it directly corresponds to the pressures inside the lung.

Measured via lumbar puncture with the patient lying on their side, normal CSF pressure is 10–18 cmH₂O in adults. Above 25 cmH₂O suggests raised intracranial pressure — potentially from a tumor, meningitis, or hydrocephalus. Below 6 cmH₂O indicates low pressure, often from a CSF leak. Neurologists use cmH₂O rather than mmHg because spinal fluid is essentially water, making the unit a direct physical analogue.

1 cmH₂O ≈ 0.981 mbar ≈ 0.0981 kPa. For bedside estimates, 1 cmH₂O ≈ 1 mbar is close enough (error under 2%). A CPAP setting of 12 cmH₂O is about 11.8 mbar or 1.18 kPa. Since respiratory equipment universally reads cmH₂O, conversion is mainly needed when interfacing with industrial instruments or when charting pressures alongside blood gas data reported in mmHg.