Biot to Watt per volt
Bi
W/V
Conversion History
| Conversion | Reuse | Delete |
|---|---|---|
1 Bi (Biot) → 10 W/V (Watt per volt) Just now · Rounding: Up to 8 significant figures | Recalculate this conversion using your current rounding settings. |
Quick Reference Table (Biot to Watt per volt)
| Biot (Bi) | Watt per volt (W/V) |
|---|---|
| 0.1 | 1 |
| 0.5 | 5 |
| 1 | 10 |
| 5 | 50 |
| 10 | 100 |
| 30 | 300 |
| 100 | 1,000 |
Results rounded to a maximum of 8 significant figures
About Biot (Bi)
The biot (Bi) is the base unit of electric current in the centimeter-gram-second electromagnetic (CGS-EMU) system. Under the traditional pre-2019 CGS-to-SI mapping retained by this converter, one biot corresponds to 10 amperes. It is defined as the current in a pair of parallel conductors 1 cm apart that produces a force of 2 dynes per centimeter length — the CGS-EMU analogue of the former force-based SI ampere definition. The biot, EMU of current, and CGS e.m. unit are exactly the same current unit within CGS-EMU. Their 10 A relationship is a historical conversion convention rather than an exact physical conversion to the post-2019 SI, in which vacuum permeability is experimentally determined. The biot is essentially obsolete in modern practice, but it appears in older physics literature and classical electrodynamics textbooks alongside the dyne, gauss, and oersted.
Under the traditional mapping used here, 1 Bi corresponds to 10 A — roughly the draw of a domestic electric kettle. References to the biot appear primarily in historical or theoretical contexts, not modern instrumentation.
Etymology: Named after Jean-Baptiste Biot (1774–1862), French physicist who, with Félix Savart, established the Biot–Savart law describing the magnetic field generated by a steady electric current.
About Watt per volt (W/V)
The watt per volt (W/V) equals one ampere, derived from the power relationship P = IV rearranged as I = P/V. A device consuming 60 W at 120 V draws 0.5 W/V = 0.5 A. The W/V form is most useful when calculating branch currents from known power ratings and supply voltages — for appliance load calculations, transformer secondary currents, or power budget analysis on a circuit board. Numerically identical to the ampere, it provides an alternative view emphasising the power-per-volt character of current and is common in power electronics and electrical installation design.
A 100 W light bulb on a 230 V supply draws approximately 0.43 W/V. A 60 W laptop adapter at 20 V delivers 3 W/V to the device.
Biot – Frequently Asked Questions
Why does this converter map one biot to 10 amperes?
The CGS-EMU system defines its base units using centimeters, grams, and seconds instead of meters, kilograms, and seconds. Under the former force-based SI ampere definition, converting the force between parallel currents made 1 Bi exactly 10 A. Since the 2019 SI redefinition, vacuum permeability is experimentally determined, so this converter retains 10 A as the stable traditional CGS-to-SI reference mapping rather than presenting it as an exact modern physical conversion.
Who was Jean-Baptiste Biot and why does he have a current unit?
Biot was a French physicist (1774–1862) who co-discovered the Biot–Savart law in 1820, describing how electric current generates a magnetic field in space. This was one of the foundational results linking electricity to magnetism. The CGS community honored him by naming their electromagnetic current unit after him.
Does anyone still use the biot in modern physics?
Essentially no. Even theorists who prefer CGS units typically use Gaussian units rather than pure CGS-EMU. The biot appears mainly in textbook conversion tables, historical physics papers, and graduate-level electrodynamics courses that teach multiple unit systems for pedagogical reasons.
How do I convert between biots and amperes?
Multiply biots by 10 to get amperes; divide amperes by 10 to get biots. A 30 A circuit carries 3 Bi; a 0.5 Bi current is 5 A. It is one of the simplest unit conversions in physics — just move the decimal point one place.
What is the Biot-Savart law and how does it relate to the biot unit?
The Biot-Savart law calculates the magnetic field produced by a small segment of current-carrying wire at any point in space. In CGS-EMU, it uses biots for current and gauss for the field. In SI it uses amperes and teslas. The law itself is fundamental — it is used to design MRI magnets, motors, and particle accelerators.
Watt per volt – Frequently Asked Questions
Why would an electrician think in watts per volt?
When sizing circuits, electricians know the appliance power (watts from the nameplate) and the supply voltage (120 V or 230 V). Dividing watts by volts gives the current in amps — which is what determines wire gauge and breaker size. "1,800 W ÷ 120 V = 15 A, so I need a 20 A circuit" is daily electrician math.
Is watts per volt ever written on any product label?
No — product labels list watts, volts, and amps separately. The W/V expression lives in textbooks and engineering calculations. But every time you read "1,500 W, 120 V" on a space heater and mentally divide to get 12.5 A, you are computing watts per volt without calling it that.
Does the watts-per-volt calculation work for AC power?
Only approximately. For AC, real power (watts) = V × I × power factor. So I = W / (V × PF). A motor rated at 1,000 W with a power factor of 0.85 on 230 V actually draws 1,000 / (230 × 0.85) = 5.1 A, not the 4.35 A that simple W/V would suggest. Always account for power factor in AC circuits.
How does watts per volt help with USB power delivery calculations?
USB PD negotiates voltage levels (5 V, 9 V, 15 V, 20 V) and maximum power (up to 240 W). Dividing the negotiated power by voltage gives the cable current: 100 W at 20 V = 5 A, requiring a 5 A rated cable. At 5 V the same 100 W would need 20 A — which is why PD uses higher voltages.
What is the relationship between watts per volt and Ohm's law?
From P = IV and V = IR, you get I = P/V = V/R = P^(1/2)/R^(1/2). The W/V form is just one of many equivalent expressions for current. Which one you use depends on what you know: power and voltage gives W/V, voltage and resistance gives V/R (Ohm's law directly).