Gigawatt to BTU (IT)/hour

1.21 GW is very real — it's about the output of a large nuclear reactor. Doc Brown needed it for the flux capacitor, but a single lightning bolt actually delivers far more instantaneous power (up to 1,000 GW) for a few microseconds. The movie got the pronunciation slightly off: Christopher Lloyd famously said "jigawatts," which is technically an acceptable older pronunciation but not the standard one.

It varies enormously. The UK peaks at about 50 GW; Germany around 80 GW; the US about 750 GW; China over 2,000 GW of installed capacity. But installed capacity and actual consumption differ: the US averages about 450 GW of actual demand. Developing nations can operate on strikingly little — some small African nations manage on under 0.5 GW for millions of people.

The Three Gorges Dam in China holds the record at 22.5 GW of installed hydroelectric capacity — enough to power a country the size of Switzerland. It has 32 main turbines each rated at 700 MW. Its annual output of ~100 TWh makes it the world's most productive power plant, though the Itaipu Dam on the Brazil-Paraguay border occasionally produces more in a given year due to higher capacity factor.

The world added roughly 420 GW of new solar capacity in 2023 alone — more than doubling the pace from just two years earlier. Total global solar capacity surpassed 1,600 GW by end of 2024. China installed over 200 GW in a single year, which is more than the entire US solar fleet accumulated over decades. At current trajectory, solar will exceed 5,000 GW globally by 2030.

A category 5 hurricane dissipates about 600,000 GW of heat energy through cloud formation alone — dwarfing human power infrastructure. A major volcanic eruption releases energy equivalent to thousands of GW sustained over hours. The Gulf Stream carries about 1.4 million GW of thermal power northward. Even a modest thunderstorm generates 10–100 GW. Nature operates on power scales that make our entire grid look like a nightlight.

The classic rule: 20 BTU/h per square foot. A 300 sq ft bedroom needs about 6,000 BTU/h; a 500 sq ft living room about 10,000 BTU/h. But this varies wildly with sun exposure (+10% for south-facing), ceiling height, insulation quality, number of occupants (+600 BTU per person), and climate zone. A room above a pizza oven in Phoenix needs more than a basement in Seattle. When in doubt, oversize slightly — an undersized unit runs constantly and never reaches setpoint.

Undersizing is obvious — the unit runs constantly and never reaches the thermostat setpoint on hot days. But oversizing is worse in subtle ways. An oversized AC cools the air quickly then shuts off before removing enough humidity, leaving you with a clammy 72°F house. The short cycles also wear the compressor faster (startup is the hardest moment) and waste energy. A 1-ton oversize in a humid climate like Florida can raise indoor humidity from a comfortable 45% to a muggy 60%. Proper Manual J load calculations matter more than most homeowners realize.

By definition, one ton of refrigeration is exactly 12,000 BTU(IT)/h, giving approximately 3.517 kW of cooling power. The name comes from the historical cooling effect of melting a short ton of ice over 24 hours. That physical origin should not be confused with an exact claim about the latent heat of every ice sample; this converter uses the fixed International Table BTU relationship.

Modern units achieve 12–25 BTU/h per watt of electricity (SEER 12–25). A SEER 20 unit removes 20 BTU/h of heat for every watt consumed — effectively a 3:1 heat pump ratio. That 12,000 BTU/h window unit draws 500–1,000 W of electricity depending on efficiency. The best mini-splits achieve SEER 30+, removing 30 BTU/h per watt, making them cheaper to run than resistive electric heaters even in heating mode.

A gas furnace's BTU/h rating is its thermal output after combustion efficiency losses (typically 80–96% of fuel input). A heat pump's BTU/h rating is the heat delivered including energy moved from outside — at COP 3, a heat pump delivering 36,000 BTU/h uses only 12,000 BTU/h worth of electricity. This makes direct BTU/h comparisons misleading: a 60,000 BTU/h furnace and a 60,000 BTU/h heat pump deliver the same heat, but the heat pump uses one-third the energy.