Horsepower (International) to BTU (IT)/minute

Mechanical horsepower uses 550 ft·lbf/s, equal to exactly 745.69987158227022 W with the international foot and standard pound-force. Metric horsepower instead uses 75 kgf·m/s, equal to 735.49875 W, while electric horsepower is defined as 746 W. The British and international selections in this converter share the mechanical definition; the labels do not imply different conversion factors.

SAE J1349 specifies measuring net horsepower with all production accessories (alternator, water pump, AC compressor) attached, at standard atmospheric conditions. Before 1972, US manufacturers used gross hp (engine on a test stand with minimal accessories), which inflated numbers by 15–25%. The switch to SAE net ratings famously caused "overnight" power drops: a Corvette went from "350 hp" (gross) to "255 hp" (net) in 1972 — same engine, honest measurement.

Japan officially uses metric PS (called 馬力, "horse power," abbreviated PS after the German). Japanese car specs list PS, and JIS standards define power in PS. However, for international export, Japanese manufacturers convert to international hp or kW depending on the destination market. A Nissan GT-R produces 570 PS for the Japanese market and 565 hp for the US market — the same engine, different unit systems, and the ~1% gap occasionally causes forum arguments.

The Wärtsilä-Sulzer RTA96-C, a marine diesel engine used in the largest container ships, produces about 109,000 hp (international) — 80,080 kW from 14 cylinders each the size of a small apartment. It's 13.5 meters tall and weighs 2,300 tonnes. At 102 RPM, it turns propellers the size of houses. For comparison, a Saturn V rocket's five F-1 engines produced about 217 million hp combined, but only for 2.5 minutes.

Probably, but slowly. The EU already legally requires kW; China uses kW; scientific and engineering communities prefer kW. But cultural inertia is powerful — Americans have been buying cars by horsepower for over a century, and "how many horses under the hood" is deeply embedded in car culture. The transition to EVs may accelerate the shift, since electric motors are naturally rated in kW. Give it 20–30 years, and hp may join the furlong and the gill in the museum of obsolete units.

During commissioning and troubleshooting, when measuring instantaneous heat output over a few minutes. If a furnace is cycling on/off and you're timing its burn cycle, you might measure 2,000 BTU/min during the 8-minute burn phase, then zero during the 4-minute off phase. This gives a clearer picture than the nameplate BTU/h rating, which assumes continuous operation and averages out the cycling.

Multiply by 60. A burner producing 1,500 BTU/min delivers 90,000 BTU/h. Going the other way, divide by 60: a 120,000 BTU/h furnace runs at 2,000 BTU/min when firing. This conversion is so routine in US HVAC work that technicians do it reflexively. The minute rate is more intuitive during short measurements; the hourly rate matches equipment nameplate conventions.

A gas stovetop burner on high: 150–250 BTU/min. A gas fireplace insert: 300–600 BTU/min. A residential water heater recovery: 500–700 BTU/min. A barbecue grill on full: 400–1,000 BTU/min. A clothes dryer: 350–600 BTU/min. These are all common US gas appliances where the original engineering was done in BTU-based units, and the nameplate may show BTU/h but the technician thinks in BTU/min during testing.

A 15 m² (160 sq ft) room in a cold climate needs roughly 100–250 BTU/min (6,000–15,000 BTU/h) of heating depending on insulation quality and outdoor temperature. A portable space heater rated 5,000 BTU/h delivers about 83 BTU/min — adequate for a small well-insulated room but insufficient for a drafty old one. The rule of thumb in US HVAC: 20–30 BTU/h per square foot, or about 0.4 BTU/min per square foot.

Almost never. The rest of the world uses watts or kilowatts for thermal power ratings. Even in countries that once used BTU (like the UK), equipment has long been rated in kW. Some Middle Eastern and Asian HVAC markets use BTU/h because they import US-manufactured equipment with American ratings, but BTU/min specifically is a niche US engineering convention. If you see it, you're almost certainly reading an American document.