Inch-Ounce to British Thermal Units (IT)

RC servo motors are rated by torque in inch-ounces (or oz·in) because the forces involved are tiny. A standard micro servo produces 40–60 in·oz, which is enough to deflect a model aircraft aileron. High-torque digital servos for 1/10-scale RC cars reach 200–400 in·oz. The inch-ounce scale gives hobbyists whole-number specs that are easy to compare.

Servo motors produce more torque at higher voltage because the motor windings draw more current and generate a stronger magnetic field. A servo rated at 60 in·oz at 4.8 V might deliver 75 in·oz at 6 V — a 25% boost. RC pilots choose voltage based on the tradeoff: 6 V gives snappier response and more holding torque for aerobatics, but draws more current and generates more heat, reducing servo lifespan. Competition flyers often run 7.4 V for maximum performance, accepting shorter gear life.

Inch-ounces give convenient whole numbers for very small torques where newton-meters would be awkward decimals (e.g., 50 in·oz ≈ 0.353 N·m). The RC hobby, miniature clockwork, and precision instrument industries in the US developed around imperial units, and the convention persists even as SI gains ground. Many datasheets now list both units side by side.

A mechanical wristwatch mainspring delivers roughly 2–5 in·oz of torque. Larger mantel clocks may have mainspring torques of 10–30 in·oz. Escapement adjustments are even finer, sometimes below 1 in·oz. Horologists use inch-ounces (or gram-centimeters) because these scales match the delicate forces in timekeeping mechanisms.

A servo's inch-ounce rating tells you the maximum force it can exert at one inch from the output shaft. A 100 in·oz servo can hold 100 ounces (6.25 lb) at 1 inch, or 50 ounces at 2 inches. Robotics designers use this to size servos for joint loads — a small robotic arm lifting 1 lb at 4 inches needs at least 64 in·oz, plus a safety margin of 50% or more.

BTU/hour expresses cooling or heating power, not energy alone. A 12,000 BTU(IT)/h rating corresponds to approximately 3,517 W of thermal power. Watts can describe thermal power as well as electrical input; the two quantities must not be confused. An air conditioner's electrical input depends on its efficiency and operating conditions, rather than being the same as its cooling capacity.

A rough rule of thumb is 20 BTU per square foot of living space in a temperate climate. A 300 sq ft bedroom needs about 6,000 BTU/h; a 1,500 sq ft open-plan living area needs roughly 30,000 BTU/h. Actual requirements vary with insulation, ceiling height, climate zone, and window area. Poorly insulated older homes may need 30–40 BTU per square foot.

BTU is a unit of energy (heat); BTU/h is a unit of power (rate of heat flow). When an air conditioner is labelled "12,000 BTU," the industry shorthand actually means 12,000 BTU per hour. Technically one BTU equals about 1,055 joules of energy, while 1 BTU/h equals about 0.293 watts. The distinction matters for energy calculations but is routinely blurred in product marketing.

Natural gas energy quantities may be billed in millions of BTU (MMBtu) or therms. A therm nominally represents 100,000 BTU, but the legal U.S. and EC therm variants have their own fixed joule definitions. This converter keeps those therm variants separate; neither should be assumed to equal exactly 100,000 BTU(IT). Always check the unit convention used on the bill.

The UK metricated energy units in the 1970s–1990s, switching gas billing from therms (100,000 BTU) to kilowatt-hours and scientific work to joules. The "British" in BTU reflects 19th-century British steam engineering origins, not current usage. Today the BTU is almost exclusively an American unit, used for HVAC, gas pricing, and appliance ratings across the US.